Well...watchguard hacking continues (o;

After figuring out that junos needs at least 256MB RAM for installation and a Firebox 2 supports 256MB I am in need for at least 2 Intel EtherExpress Pro 100 PCI cards as Juniper only supports Intel and certain Broadcom chipsets now...

The rest is fine (o;

Copyright (c) 1996-2001, Juniper Networks, Inc. All rights reserved. Copyright (c) 1992-2001 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. JUNOS 7.0R2.7 #0: 2005-01-06 06:58:15 UTC

builder@benten.juniper.net:/build/benten-c/7.0R2.7/obj-i386/sys/compile/JUNI PER Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 200455806 Hz CPU: Pentium/P55C (200.46-MHz 586-class CPU) Origin = "GenuineIntel" Id = 0x543 Stepping = 3 Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX> real memory = 268435456 (262144K bytes) FreeBSD Kernel Configuration Utility - Version 1.2 Type "help" for help or "visual" to go to the visual configuration interface (requires MGA/VGA display or serial terminal capable of displaying ANSI graphics). config> di psm0 config> q sio0: gdb debugging port avail memory = 253788160 (247840K bytes) Preloaded elf kernel "kernel" at 0xc06de000. Intel Pentium detected, installing workaround for F00F bug DEVFS: ready for devices md0: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port 0xfcd0-0xfcdf at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 15 smb0: <Intel 82371AB SMB controller> port 0x1040-0x104f at device 7.3 on pci0 pci0: <unknown card> (vendor=0x1011, dev=0x0019) at 13.0 irq 10 pci0: <unknown card> (vendor=0x1011, dev=0x0019) at 14.0 irq 11 pci0: <unknown card> (vendor=0x1011, dev=0x0019) at 15.0 irq 9 pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> at device 16.0 on pci0 pcic-pci0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC se rial isa irq] pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> at device 16.1 on pci0 pcic-pci1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC se pci0: <S3 Trio 64V2/DX/GX graphics accelerator> at 18.0 irq 15 fdc0: direction bit not set fdc0: cmd 3 failed at out byte 1 of 3 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 irq 10 on isa0 pcic0: management irq 10 pccard0: <PC Card bus -- legacy version> on pcic0 pccard1: <PC Card bus -- legacy version> on pcic0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x90 on isa0 sio0: type 16550A, console sio1: configured irq 5 not in bitmap of probed irqs 0 sio2 at port 0x2f8-0x2ff irq 3 on isa0 sio2: type 16550A sio3: configured irq 7 not in bitmap of probed irqs 0 DEVFS: ready to run ad0: 11513MB <FUJITSU MHK2120AT> [23392/16/63] at ata0-master using UDMA33 ad1: 7MB <> [248/2/32] at ata0-slave using PIO2 root@%

nice weekend rick

i'm sorry, don't one of your cards below.

but as far as i remember easynet has a lot of etherexpress pro built into servers.. you might consider about replacing just one of those cards...

-steven

-----Original Message----- From: swinog-bounces@lists.swinog.ch [mailto:swinog-bounces@lists.swinog.ch]On Behalf Of Richard Klingler Sent: Thursday, December 15, 2005 9:47 PM To: swinog@swinog.ch Subject: [swinog] Broadcom GB NIC

Evenin' (o;

As apparently no one has fxp cards at hand (or is willing to sell ;o)...I'll updated the list of working cards I'm looking for:

• Intel 82801CAM (ICH3) Pro/100 VE Ethernet
• Intel InBusiness 10/100 Ethernet
• Intel Embedded 10/100 Ethernet
• Intel EtherExpress Pro 10/100B Ethernet
• Broadcom 5700 Ethernet LAN controller
• Broadcom Strataswitch BCM5615 10/100/1000B Ethernet

thanx in advance rick

(can't afford j2600 personally ;o)

---

swinog mailing list swinog@lists.swinog.ch http://lists.swinog.ch/cgi-bin/mailman/listinfo/swinog